Universal Laser Systems Laser Platform M-300 Guía para resolver problemas Pagina 59
- Pagina / 100
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
6-6 Maintenance
Exhaust Plenum Cleaning
• Power system OFF.
• Remove the Z-axis table.
• Remove the two thumbscrews.
• Lift the Plenum straight up, off of the hooks, and
out of the system.
• Clean the Plenum and inside the Laser System.
• Installation is opposite of removal. Make sure that the Plenum rests on the hooks.
Adjustments and Lubrication
There are no periodic adjustments required. The bearings in the motion system will self adjust
to take up any clearances as they begin to wear. The belts are fiber reinforced and will not
stretch under normal use so that periodic tension adjustment is not necessary. Optical
alignment is not necessary because the laser and the #2 Mirror are fixed.
All bearings in the system are sealed and do not require lubrication. DO NOT lubricate the
tracks that the bearings ride in. The only lubrication that may be required is the screw threads
for the table lifting mechanism. After some time, contaminants can adhere to the lubricant,
which can cause the engraving table to bind up or sound squeaky. If this is the case, wipe off
the contaminated grease with a soft cloth and apply fresh white lithium grease to the screw
threads. Run the table up and down to work in the fresh grease.
Electronic Upgrading
The laser systems onboard computer is equipped with a special “Flash” upgrade technology. If
the electronic operation of the system should ever require upgrading, it can be done
electronically without the changing of any parts. The upgrade file gets downloaded from your
computer to the laser system via the parallel port. This file is then run on the laser system and it
only takes a few minutes. Once the file has completely run, the laser system will automatically
restart and the new changes will take effect. For more specific details, please refer to the
instructions that will accompany the flash disk.
- 16008 North 81st Street 1
- Scottsdale, AZ 85260 USA 1
- Customer Support Department 1
- Phone: 480-609-0297 1
- Fax: 480-609-1203 1
- By Vince Budetti 2
- All Rights Reserved 2
- Introduction 3
- How To Get Help 3
- Table of Contents 4
- SECTION 6 – Maintenance 5
- Appendices 6
- General Safety 7
- Laser Safety 8
- Safety Labels 8
- SERIAL #: 02500A 9
- DATE : MAY 2000 9
- Safety Label Locations 10
- EU Compliance (CE) 11
- FCC Compliance 12
- Installation 13
- Exhaust Requirements 14
- Laser Cooling Requirements 15
- Assembling the Laser 16
- Laser Cartridge Installation 17
- Computer Requirements 19
- Making the Connections 19
- Problem Prevention 20
- System Operation 21
- UPDOWNSTOPSTART 22
- Computerized Controls 27
- Printer Driver Controls 28
- Power / Speed 29
- % Power 29
- % Speed 29
- 2.0” Lens 30
- 1000 DPI 31
- Add Shoulder 32
- Print Negative 32
- Mirror Image 32
- Graphics 33
- Tuning Tab 34
- Vector Scaling 36
- Upgrading the Printer Driver 37
- Upgrading the Firmware 37
- Software Suggestions 38
- General Software Setup 38
- Page Setup 39
- Ruler Setup 39
- Outlines and Fills 40
- Image Processing Order 41
- Overlapping Fills 41
- Overlapping Outlines 41
- Speed Optimizing 42
- Postscript (PS) Images 42
- Font Requirements 43
- CorelDRAW 8 44
- CorelDRAW 9 45
- Software Setup – AutoCAD 46
- Using the Laser System 49
- Step-by-Step 49
- Focusing 50
- Printing to the Laser System 51
- Maintenance 54
- System Cleaning 56
- Optics Cleaning 56
- Z-axis Table Removal 58
- Exhaust Plenum Cleaning 59
- Adjustments and Lubrication 59
- Electronic Upgrading 59
- Battery Replacement 60
- Cooling Fan Filters 60
- Maintenance Schedule 61
- Material Applications 62
- Materials 63
- Sample Materials 7-5 66
- Sample Materials 7-7 68
- Sample Materials 7-9 70
- MALE FEMALE 73
- Sample Materials 7-13 74
- Sample Materials 7-15 76
- Sample Materials 7-17 78
- Sample Materials 7-19 80
- Sample Materials 7-21 82
- Sample Materials 7-23 84
- BLACK FILLED BOX 85
- MIRRORED IMAGE 85
- LASER ENGRAVING TABLE 86
- Bitmapped or Scanned Images 87
- Monochrome Bitmaps 88
- Grayscale Bitmaps 88
- Color Bitmaps 89
- Focus Lens Kits 91
- APPENDIX 93
- Appendix B - Specifications 95
- Engraving Quality 96
- Operational 99
- Appendix D - How To Get Help 100
Relacionado con productos y manuales para Niveles Láser Universal Laser Systems Laser Platform M-300
(14 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.049 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales