Universal Laser Systems Laser Platform M-300 Guía para resolver problemas Pagina 49
- Pagina / 100
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
SECTION 5
Using the Laser System
Step-by-Step
In this section we will cover how to completely use the laser system to create a product from
start to finish. From powering on everything to removing the finished product from the system,
we will cover the entire process step by step. As an example, let’s engrave and cut out a key
chain from a 2 by 4 inch, 1/8 inch thick piece of hardwood.
WARNING: Before continuing, please ensure that you have completely read
and understood the entire manual up to this point. It is essential that you
know how to safely operate the laser system before you actually engrave or
cut any material.
Creating the Graphic
In your graphics program set your page size to the
maximum size of the engraving area, 16 inches
wide by 12 inches tall in the Landscape mode.
Create some text with a BLACK colored fill and
NO outline. For example, type in the word
“Keychain”. Draw an outline box around the text,
color the outline RED, give the outline a thickness
of .00005 inches (or the smallest possible line
width), remove the fill color (if any), and round the
edges if desired. Now add a circle with the same
RED outline .00005 inches (or the smallest
possible line width) and NO fill, for the key ring.
Place the graphic into the upper left corner of the page, on screen, relative to how the piece of
wood is positioned in the engraving area as the diagram illustrates.
Powering ON the Laser System
Always power ON your computer and let it boot up completely BEFORE powering ON the laser
system otherwise your laser system can “lock up” when attempting to run the first file. If the
laser system “locks up” during the engraving or cutting process, it can destroy your material and
require the laser system to be powered OFF and then ON again to clear the error. The Green
light will stop flashing and remain OFF when the system is finished homing and is ready to
accept a file.
- 16008 North 81st Street 1
- Scottsdale, AZ 85260 USA 1
- Customer Support Department 1
- Phone: 480-609-0297 1
- Fax: 480-609-1203 1
- By Vince Budetti 2
- All Rights Reserved 2
- Introduction 3
- How To Get Help 3
- Table of Contents 4
- SECTION 6 – Maintenance 5
- Appendices 6
- General Safety 7
- Laser Safety 8
- Safety Labels 8
- SERIAL #: 02500A 9
- DATE : MAY 2000 9
- Safety Label Locations 10
- EU Compliance (CE) 11
- FCC Compliance 12
- Installation 13
- Exhaust Requirements 14
- Laser Cooling Requirements 15
- Assembling the Laser 16
- Laser Cartridge Installation 17
- Computer Requirements 19
- Making the Connections 19
- Problem Prevention 20
- System Operation 21
- UPDOWNSTOPSTART 22
- Computerized Controls 27
- Printer Driver Controls 28
- Power / Speed 29
- % Power 29
- % Speed 29
- 2.0” Lens 30
- 1000 DPI 31
- Add Shoulder 32
- Print Negative 32
- Mirror Image 32
- Graphics 33
- Tuning Tab 34
- Vector Scaling 36
- Upgrading the Printer Driver 37
- Upgrading the Firmware 37
- Software Suggestions 38
- General Software Setup 38
- Page Setup 39
- Ruler Setup 39
- Outlines and Fills 40
- Image Processing Order 41
- Overlapping Fills 41
- Overlapping Outlines 41
- Speed Optimizing 42
- Postscript (PS) Images 42
- Font Requirements 43
- CorelDRAW 8 44
- CorelDRAW 9 45
- Software Setup – AutoCAD 46
- Using the Laser System 49
- Step-by-Step 49
- Focusing 50
- Printing to the Laser System 51
- Maintenance 54
- System Cleaning 56
- Optics Cleaning 56
- Z-axis Table Removal 58
- Exhaust Plenum Cleaning 59
- Adjustments and Lubrication 59
- Electronic Upgrading 59
- Battery Replacement 60
- Cooling Fan Filters 60
- Maintenance Schedule 61
- Material Applications 62
- Materials 63
- Sample Materials 7-5 66
- Sample Materials 7-7 68
- Sample Materials 7-9 70
- MALE FEMALE 73
- Sample Materials 7-13 74
- Sample Materials 7-15 76
- Sample Materials 7-17 78
- Sample Materials 7-19 80
- Sample Materials 7-21 82
- Sample Materials 7-23 84
- BLACK FILLED BOX 85
- MIRRORED IMAGE 85
- LASER ENGRAVING TABLE 86
- Bitmapped or Scanned Images 87
- Monochrome Bitmaps 88
- Grayscale Bitmaps 88
- Color Bitmaps 89
- Focus Lens Kits 91
- APPENDIX 93
- Appendix B - Specifications 95
- Engraving Quality 96
- Operational 99
- Appendix D - How To Get Help 100
Relacionado con productos y manuales para Niveles Láser Universal Laser Systems Laser Platform M-300
(14 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.058 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales