Universal Laser Systems Laser Platform M-300 Guía para resolver problemas Pagina 19
- Pagina / 100
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Installation 2-7
Computer Requirements
The following is the MINIMUM required computer configuration. Using a faster computer with
more capacity will increase efficiency and throughput. Although using a computer that does not
meet our minimum recommendation might be acceptable to you, a faster computer will definitely
pay for itself in a short amount of time.
• Pentium 300 MHz or equivalent
• 32 MB of RAM
• 4 Gigabyte hard drive or bigger (with at least 2 Gigabytes of free space)
• 8 MB Video Card
• 17 inch color VGA monitor
• 3.5” floppy disk drive
• CD-ROM Drive
• Mouse or other pointing device
• Microsoft Windows 95 or 98
• 600 DPI Optical Resolution Scanner
• Second or third LPT (parallel) port
Remember that the laser system is an output device just like a printer is. The faster you can
create graphics and manipulate your software, the faster you can download to the laser system.
Making the Connections
Please make the following connections in the exact order described otherwise static electricity
can damage the computer and/or the laser system’s electronics.
• Connect the laser system’s Power Cord and your computer’s Power Cord to the electrical
outlet(s). DO NOT power ON either unit at this time.
• This laser engraving system requires a special 6 foot (1.8 meter) parallel cable (supplied
with system) to connect to the computer system. DO NOT USE A CABLE FROM
ANOTHER MANUFACTURER, OTHERWISE DAMAGE THE LASER SYSTEM MAY
OCCUR. ALSO, DO NOT USE ANY ADAPTERS TO LENGTHEN THE SPECIAL CABLE.
YOU MUST PLACE YOUR COMPUTER SYSTEM WITHIN 6 FEET OF THE LASER
SYSTEM TO MAKE THE CONNECTION. Connect the special cable to the laser system
and to the parallel port on the computer.
• Power ON your computer and check your computers BIOS setting for your parallel port.
Make sure that it is set preferably to “Standard Parallel Port (SPP)”, “Normal”, or “Output
Only”. If one of the first three choices is not available set it to “ECP”. DO NOT SET IT TO
“EPP” or “Bi-directional”. The laser system does not support these modes. If your
computer is set to an incorrect configuration, erroneous data will be sent to the laser system
during printing. This can cause the system to lock up, print garbage information, or not print
at all. For information on how to check or adjust your computers BIOS setting, please refer
to your computer’s owner manual or contact their technical support department.
- 16008 North 81st Street 1
- Scottsdale, AZ 85260 USA 1
- Customer Support Department 1
- Phone: 480-609-0297 1
- Fax: 480-609-1203 1
- By Vince Budetti 2
- All Rights Reserved 2
- Introduction 3
- How To Get Help 3
- Table of Contents 4
- SECTION 6 – Maintenance 5
- Appendices 6
- General Safety 7
- Laser Safety 8
- Safety Labels 8
- SERIAL #: 02500A 9
- DATE : MAY 2000 9
- Safety Label Locations 10
- EU Compliance (CE) 11
- FCC Compliance 12
- Installation 13
- Exhaust Requirements 14
- Laser Cooling Requirements 15
- Assembling the Laser 16
- Laser Cartridge Installation 17
- Computer Requirements 19
- Making the Connections 19
- Problem Prevention 20
- System Operation 21
- UPDOWNSTOPSTART 22
- Computerized Controls 27
- Printer Driver Controls 28
- Power / Speed 29
- % Power 29
- % Speed 29
- 2.0” Lens 30
- 1000 DPI 31
- Add Shoulder 32
- Print Negative 32
- Mirror Image 32
- Graphics 33
- Tuning Tab 34
- Vector Scaling 36
- Upgrading the Printer Driver 37
- Upgrading the Firmware 37
- Software Suggestions 38
- General Software Setup 38
- Page Setup 39
- Ruler Setup 39
- Outlines and Fills 40
- Image Processing Order 41
- Overlapping Fills 41
- Overlapping Outlines 41
- Speed Optimizing 42
- Postscript (PS) Images 42
- Font Requirements 43
- CorelDRAW 8 44
- CorelDRAW 9 45
- Software Setup – AutoCAD 46
- Using the Laser System 49
- Step-by-Step 49
- Focusing 50
- Printing to the Laser System 51
- Maintenance 54
- System Cleaning 56
- Optics Cleaning 56
- Z-axis Table Removal 58
- Exhaust Plenum Cleaning 59
- Adjustments and Lubrication 59
- Electronic Upgrading 59
- Battery Replacement 60
- Cooling Fan Filters 60
- Maintenance Schedule 61
- Material Applications 62
- Materials 63
- Sample Materials 7-5 66
- Sample Materials 7-7 68
- Sample Materials 7-9 70
- MALE FEMALE 73
- Sample Materials 7-13 74
- Sample Materials 7-15 76
- Sample Materials 7-17 78
- Sample Materials 7-19 80
- Sample Materials 7-21 82
- Sample Materials 7-23 84
- BLACK FILLED BOX 85
- MIRRORED IMAGE 85
- LASER ENGRAVING TABLE 86
- Bitmapped or Scanned Images 87
- Monochrome Bitmaps 88
- Grayscale Bitmaps 88
- Color Bitmaps 89
- Focus Lens Kits 91
- APPENDIX 93
- Appendix B - Specifications 95
- Engraving Quality 96
- Operational 99
- Appendix D - How To Get Help 100
Relacionado con productos y manuales para Niveles Láser Universal Laser Systems Laser Platform M-300
(14 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.213 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales