Universal Laser Systems Laser Platform M-300 Guía para resolver problemas Pagina 15
- Pagina / 100
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Installation 2-3
• The airflow gate is used to
control the flow of air for
different applications. Some
applications, such as deep
wood engraving, that produce a
large amount of smoke or
particulate matter will usually
require the gate to be
completely open whereas
lighter contamination-producing
applications, such as paper
cutting, may only need small
amount of airflow. Also, when
the laser system is OFF you
can close this gate to prevent
the outside environment from
entering your laser system.
This would be very useful in
colder climates where it can be
damaging to the laser system
to have extremely cold air
come into it from the outside.
• Install an ON/OFF switch, for
your blower, in the same room
as your laser system.
WARNING: For
general, personal, and environmental safety reasons, we recommend the design
and installation of the exhaust system by a licensed contractor to meet safety
and local code requirements as well as providing a proper exhaust system that
the laser system requires to validate your warranty.
Laser Cooling Requirements
This type of laser system uses fans to keep the laser cartridge and electronics cooled during
operation. Maintain the room temperature at the recommended ambient temperature range
outlined previously in the Operating Environment section.
WARNING: Do not confine the back of the machine by surrounding it with
furniture, shelving, backing it into a corner, etc. The backside of the laser system
must be allowed to “Breathe” otherwise it can overheat the laser cartridge, power
supply, and/or the CPU module. Overheating may cause serious and very costly
damage to the laser system and may invalidate your warranty.
I
2
3
4
5
6
7
1) High Pressure Exhaust Blower
2) Weather-proof Cover
3) Rigid Ducting
4) Airflow Gate
5) Reducer
6) 2 ½ inch Industrial Grade Flexible Tubing
7) On/Off Switch
- 16008 North 81st Street 1
- Scottsdale, AZ 85260 USA 1
- Customer Support Department 1
- Phone: 480-609-0297 1
- Fax: 480-609-1203 1
- By Vince Budetti 2
- All Rights Reserved 2
- Introduction 3
- How To Get Help 3
- Table of Contents 4
- SECTION 6 – Maintenance 5
- Appendices 6
- General Safety 7
- Laser Safety 8
- Safety Labels 8
- SERIAL #: 02500A 9
- DATE : MAY 2000 9
- Safety Label Locations 10
- EU Compliance (CE) 11
- FCC Compliance 12
- Installation 13
- Exhaust Requirements 14
- Laser Cooling Requirements 15
- Assembling the Laser 16
- Laser Cartridge Installation 17
- Computer Requirements 19
- Making the Connections 19
- Problem Prevention 20
- System Operation 21
- UPDOWNSTOPSTART 22
- Computerized Controls 27
- Printer Driver Controls 28
- Power / Speed 29
- % Power 29
- % Speed 29
- 2.0” Lens 30
- 1000 DPI 31
- Add Shoulder 32
- Print Negative 32
- Mirror Image 32
- Graphics 33
- Tuning Tab 34
- Vector Scaling 36
- Upgrading the Printer Driver 37
- Upgrading the Firmware 37
- Software Suggestions 38
- General Software Setup 38
- Page Setup 39
- Ruler Setup 39
- Outlines and Fills 40
- Image Processing Order 41
- Overlapping Fills 41
- Overlapping Outlines 41
- Speed Optimizing 42
- Postscript (PS) Images 42
- Font Requirements 43
- CorelDRAW 8 44
- CorelDRAW 9 45
- Software Setup – AutoCAD 46
- Using the Laser System 49
- Step-by-Step 49
- Focusing 50
- Printing to the Laser System 51
- Maintenance 54
- System Cleaning 56
- Optics Cleaning 56
- Z-axis Table Removal 58
- Exhaust Plenum Cleaning 59
- Adjustments and Lubrication 59
- Electronic Upgrading 59
- Battery Replacement 60
- Cooling Fan Filters 60
- Maintenance Schedule 61
- Material Applications 62
- Materials 63
- Sample Materials 7-5 66
- Sample Materials 7-7 68
- Sample Materials 7-9 70
- MALE FEMALE 73
- Sample Materials 7-13 74
- Sample Materials 7-15 76
- Sample Materials 7-17 78
- Sample Materials 7-19 80
- Sample Materials 7-21 82
- Sample Materials 7-23 84
- BLACK FILLED BOX 85
- MIRRORED IMAGE 85
- LASER ENGRAVING TABLE 86
- Bitmapped or Scanned Images 87
- Monochrome Bitmaps 88
- Grayscale Bitmaps 88
- Color Bitmaps 89
- Focus Lens Kits 91
- APPENDIX 93
- Appendix B - Specifications 95
- Engraving Quality 96
- Operational 99
- Appendix D - How To Get Help 100
Relacionado con productos y manuales para Niveles Láser Universal Laser Systems Laser Platform M-300
(14 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.119 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales