Universal Laser Systems Laser Platform M-300 Guía para resolver problemas Pagina 20
- Pagina / 100
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
2-8 Installation
• Power ON the laser system. After the system finishes
initializing, it will “home” itself in the upper right corner of the
engraving area. This process takes about 30 seconds.
• We will now check if the Laser Cartridge was installed
properly. To do this, open the top door and place a small
piece of masking tape across the ¾” hole in the focus
carriage. Gently rub the tape around the edge of the hole
so that you can see the outline of the hole through the tape.
• Once you open the top door, the red diode pointer will
illuminate and a red dot will appear on the masking tape.
The dot should appear centered, or close to the center of
the hole, within 1/8”. If not, remove and re-install the laser
cartridge and try again. If the red dot still does not appear
within 1/8” of the center of the hole, please contact our
Service Department.
• If the red dot is centered, installation is complete. Remove
the masking tape and power OFF the system at this time.
Problem Prevention
The following are things that you MUST NEVER
do:
1) Never connect or disconnect the printer cable while either the computer or the
laser system is powered ON. Always power OFF both the laser system and the computer
but leave them plugged into the wall outlet when connecting or disconnecting the printer cable.
2) Never connect the laser system through a manual switch type A/B switch box.
If connecting an additional laser system or other printer to the same computer, we recommend
the installation of an additional parallel port into the computer. Using a switchbox can create
electrical noise that can cause an engraving problem or can damage the laser system and/or
the computer’s electronics.
3) Never use any device that is installed between the computers parallel port and
the parallel port of the laser system such as a ZIP drive, parallel port CD-ROM
drive or software keys (dongles).
This can not only damage the laser systems electronics
but it usually will not work and will cause file transmission errors. Again, install an additional
parallel port for other peripheral devices.
I
2
3
1) Masking Tape
2) Outline of Hole
3) Red Dot
- 16008 North 81st Street 1
- Scottsdale, AZ 85260 USA 1
- Customer Support Department 1
- Phone: 480-609-0297 1
- Fax: 480-609-1203 1
- By Vince Budetti 2
- All Rights Reserved 2
- Introduction 3
- How To Get Help 3
- Table of Contents 4
- SECTION 6 – Maintenance 5
- Appendices 6
- General Safety 7
- Laser Safety 8
- Safety Labels 8
- SERIAL #: 02500A 9
- DATE : MAY 2000 9
- Safety Label Locations 10
- EU Compliance (CE) 11
- FCC Compliance 12
- Installation 13
- Exhaust Requirements 14
- Laser Cooling Requirements 15
- Assembling the Laser 16
- Laser Cartridge Installation 17
- Computer Requirements 19
- Making the Connections 19
- Problem Prevention 20
- System Operation 21
- UPDOWNSTOPSTART 22
- Computerized Controls 27
- Printer Driver Controls 28
- Power / Speed 29
- % Power 29
- % Speed 29
- 2.0” Lens 30
- 1000 DPI 31
- Add Shoulder 32
- Print Negative 32
- Mirror Image 32
- Graphics 33
- Tuning Tab 34
- Vector Scaling 36
- Upgrading the Printer Driver 37
- Upgrading the Firmware 37
- Software Suggestions 38
- General Software Setup 38
- Page Setup 39
- Ruler Setup 39
- Outlines and Fills 40
- Image Processing Order 41
- Overlapping Fills 41
- Overlapping Outlines 41
- Speed Optimizing 42
- Postscript (PS) Images 42
- Font Requirements 43
- CorelDRAW 8 44
- CorelDRAW 9 45
- Software Setup – AutoCAD 46
- Using the Laser System 49
- Step-by-Step 49
- Focusing 50
- Printing to the Laser System 51
- Maintenance 54
- System Cleaning 56
- Optics Cleaning 56
- Z-axis Table Removal 58
- Exhaust Plenum Cleaning 59
- Adjustments and Lubrication 59
- Electronic Upgrading 59
- Battery Replacement 60
- Cooling Fan Filters 60
- Maintenance Schedule 61
- Material Applications 62
- Materials 63
- Sample Materials 7-5 66
- Sample Materials 7-7 68
- Sample Materials 7-9 70
- MALE FEMALE 73
- Sample Materials 7-13 74
- Sample Materials 7-15 76
- Sample Materials 7-17 78
- Sample Materials 7-19 80
- Sample Materials 7-21 82
- Sample Materials 7-23 84
- BLACK FILLED BOX 85
- MIRRORED IMAGE 85
- LASER ENGRAVING TABLE 86
- Bitmapped or Scanned Images 87
- Monochrome Bitmaps 88
- Grayscale Bitmaps 88
- Color Bitmaps 89
- Focus Lens Kits 91
- APPENDIX 93
- Appendix B - Specifications 95
- Engraving Quality 96
- Operational 99
- Appendix D - How To Get Help 100
Relacionado con productos y manuales para Niveles Láser Universal Laser Systems Laser Platform M-300
(14 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.087 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales