Universal Laser Systems Laser Platform M-300 Guía para resolver problemas Pagina 52
- Pagina / 100
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
5-4 Using the Laser System Step-by-Step
A status screen may now appear showing a percentage of completion. Once this status screen
disappears, it does not mean that the file is totally in the laser systems memory. If you have the
Windows 95/98 print spooler turned on, it can take several seconds to even minutes, depending
on your file size and the speed of your computer, before the entire file loads into the laser
systems memory. As the file is downloading, the Green Light on the control Panel will start
flashing. Once the entire file is completely loaded, the Green Light on the Control Panel will
stop flashing and remain ON.
Starting the Engraving Process
Before pressing the “START” button on the control panel:
• Turn on your exhaust system.
• Make sure your material is positioned correctly within the engraving area.
• Make sure that you are properly focused.
• Make sure that the top door is closed.
If all of the above has been verified, press the “START” button on the laser systems control
panel to begin the engraving process.
WARNING: Observe that the laser system is functioning as desired. If any abnormalities are
present, including but not limited to, flaming, sparking, melting, or excessive smoking of the
material you are engraving, STOP THE ENGRAVING PROCESS IMMEDIATELY BY EITHER
PRESSING THE “STOP” BUTTON OR OPENING THE TOP DOOR! Re-check your settings in
the printer driver as well as the laser system. If everything seems to be correct, the material is
not suitable for laser engraving or cutting and you MUST DISCONTINUE processing this
material or any material that is shows signs of damaging the equipment. NEVER LEAVE THE
LASER SYSTEM UNATTENDED DURING THE ENGRAVING OR CUTTING PROCESS.
While the laser system is processing your material, you may stop the process by opening the
top door, or pressing the Stop button. However, interrupting the engraving or cutting process
may ruin your application material because you will be unable to resume operation where you
left off. Pressing the Start button will start the file over from the beginning.
- 16008 North 81st Street 1
- Scottsdale, AZ 85260 USA 1
- Customer Support Department 1
- Phone: 480-609-0297 1
- Fax: 480-609-1203 1
- By Vince Budetti 2
- All Rights Reserved 2
- Introduction 3
- How To Get Help 3
- Table of Contents 4
- SECTION 6 – Maintenance 5
- Appendices 6
- General Safety 7
- Laser Safety 8
- Safety Labels 8
- SERIAL #: 02500A 9
- DATE : MAY 2000 9
- Safety Label Locations 10
- EU Compliance (CE) 11
- FCC Compliance 12
- Installation 13
- Exhaust Requirements 14
- Laser Cooling Requirements 15
- Assembling the Laser 16
- Laser Cartridge Installation 17
- Computer Requirements 19
- Making the Connections 19
- Problem Prevention 20
- System Operation 21
- UPDOWNSTOPSTART 22
- Computerized Controls 27
- Printer Driver Controls 28
- Power / Speed 29
- % Power 29
- % Speed 29
- 2.0” Lens 30
- 1000 DPI 31
- Add Shoulder 32
- Print Negative 32
- Mirror Image 32
- Graphics 33
- Tuning Tab 34
- Vector Scaling 36
- Upgrading the Printer Driver 37
- Upgrading the Firmware 37
- Software Suggestions 38
- General Software Setup 38
- Page Setup 39
- Ruler Setup 39
- Outlines and Fills 40
- Image Processing Order 41
- Overlapping Fills 41
- Overlapping Outlines 41
- Speed Optimizing 42
- Postscript (PS) Images 42
- Font Requirements 43
- CorelDRAW 8 44
- CorelDRAW 9 45
- Software Setup – AutoCAD 46
- Using the Laser System 49
- Step-by-Step 49
- Focusing 50
- Printing to the Laser System 51
- Maintenance 54
- System Cleaning 56
- Optics Cleaning 56
- Z-axis Table Removal 58
- Exhaust Plenum Cleaning 59
- Adjustments and Lubrication 59
- Electronic Upgrading 59
- Battery Replacement 60
- Cooling Fan Filters 60
- Maintenance Schedule 61
- Material Applications 62
- Materials 63
- Sample Materials 7-5 66
- Sample Materials 7-7 68
- Sample Materials 7-9 70
- MALE FEMALE 73
- Sample Materials 7-13 74
- Sample Materials 7-15 76
- Sample Materials 7-17 78
- Sample Materials 7-19 80
- Sample Materials 7-21 82
- Sample Materials 7-23 84
- BLACK FILLED BOX 85
- MIRRORED IMAGE 85
- LASER ENGRAVING TABLE 86
- Bitmapped or Scanned Images 87
- Monochrome Bitmaps 88
- Grayscale Bitmaps 88
- Color Bitmaps 89
- Focus Lens Kits 91
- APPENDIX 93
- Appendix B - Specifications 95
- Engraving Quality 96
- Operational 99
- Appendix D - How To Get Help 100
Relacionado con productos y manuales para Niveles Láser Universal Laser Systems Laser Platform M-300
(14 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.031 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales